Products

RadioPRO4 Interface for Ford Vehicles with CAN bus

$239.00 RP4-FD11

RadioPRO4 Interface for Ford Vehicles with CAN bus

  • Does not retain SYNC. SYNC retention requires the MS-FRD1.
  • Factory amplified Systems will not fade as neither the aftermarket radio or the RP interface have the ability to control the amplifier’s fader.

Vehicle Specific Notes

  • 2013-2014 F-150: Only compatible in base model trucks equipped with the center stack radio (pictured below)

Center Stack Radio

  • 2008 - 2010 F-250/350/450: Not compatible with model trim XL (fleet vehicles). These vehicles do not have the necessary CAN bus signals
  • 2013 -2016 Ford Super Duty: Only compatible in base model trucks equipped with the double DIN radio (pictured below)

Double DIN Radio

RP4-FD11

RadioPRO4 Interface for Ford Vehicles with CAN bus

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

  • If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
  • Download the firmware file to a location on your computer that you can easily find.
  • Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
  • Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
  • Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
  • Select your RP Interface from the "Interface select" pull down menu.
  • Click "Update firmware". The new firmware can be found where you saved it before beginning.
  • Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

  • Firmware Download, Version 1.5.4.6 (Released on February 14th, 2020)
    Release Notes
    • Changes JVC default function on "Select" button from "OK" to "Band"
    Download
  • Firmware Download, Version 1.5.4.5 (Released on June 23rd, 2015)
    Release Notes
    • Adds 2013-2016 Ford Super Duty applications

    Download
  • Firmware Download, Version 1.5.4.4 (Released on February 13th, 2015)
    Release Notes
    • Adds Fusion
    • Separates Sony & Pioneer
    • Adds Alpine VR command
    • Fixes LED problem without proper radio selection
    Download
  • Firmware Download, Version 1.2.3.3 (Released on May 10th, 2013)
    Release Notes
    • Adds short press long press dual command functionality for SWC
    • Fixes issues seen with SWC when used with new Alpine & JVC head units
    • Adds new Kenwood Bluetooth function support for SWC
    • Fixes issues with Reverse, Parking Break, and Illumination not working in older vehicles
    • Adds re-calibration of OE Steering Wheel Controls to accommodate other vehicles and to improve SWC detection
    Download
  • Firmware Download, Version 1.1.2 (Released on June 4th, 2012)
    Release Notes
    • Fixes THX amplifier not turning on in 2012+ Lincoln Navigator
    Download
  • Firmware Download, Version 1.1.1 (Released on April 5th, 2012)
    Release Notes
    • Initial Release
    Download
  • Utility/Other, Version 2.6 (Released on July 21st, 2017)
    Release Notes
    PAC-UP Interface Updater
    Download

An all-in-one radio replacement and SWC interface, the innovative RadioPRO4 comes pre-loaded with amplifier retention and SWC software, navigation-based output signals, and other features that save time and money during installation.

  • Retains steering wheel controls (pre-programmed)
  • Data controlled accessory and navigation outputs
  • Retains factory amplifier
  • Retains Rear Seat Controls
  • Provides factory RSE activation
  • In package updatable using the PAC-UP

Provides

  • 12V ACC output (RAP)
  • Vehicle Speed Sense (VSS)
  • Retains factory amplifier
  • Illumination
  • Reverse Trigger
  • Parking brake output

Patent # 8,014,540 & 8,184,825

RP4-FD11 Instruction Manual
Rev 1.3 ***These only apply to modules that are paired with harnesses labeled V2 or higher***
 Download (1.09M)
RP4-FD11 Instruction Manual
Rev. 012015
 Download (1.2M)