RadioPRO4 Interface for Select 2013-2018 Chrysler Vehicles with CAN bus
Replace your radio, not your features
| Year(s) | Make | Model | Trim Level | Additional Info |
|---|---|---|---|---|
| 2014-2015 | DODGE | DURANGO | ALL TRIM LEVELS | — |
| 2013-2018 | DODGE | RAM TRUCK | ALL TRIM LEVELS | — |
| 2014-2015 | JEEP | CHEROKEE | ALL TRIM LEVELS | — |
| 2014-2015 | JEEP | GRAND CHEROKEE | ALL TRIM LEVELS | — |
| 2014-2015 | RAM | PROMASTER | ALL TRIM LEVELS | — |
| 2015 | RAM | PROMASTER CITY | ALL TRIM LEVELS | — |
| 2013-2018 | RAM | RAM TRUCK | ALL TRIM LEVELS | — |
- RAM Promaster: Not compatible in trucks equipped with a factory single DIN radio
- 2016-2018 RAM Truck with uConnect 5.0 and 8.4 systems: Does not retain the ability to change all vehicle settings, including horn honk with lock and fuel saver display (does not affect Uconnect 2.0 system).
- Does not retain uConnect
- Retention of the VES system is not currently supported
- In vehicles equipped with the 8.4” uConnect system, the factory compass display on the DIC, 911 assist, WiFi hotspot and uConnect access will be lost
- In vehicles equipped with reverse sensors, but are not equipped with a factory amplified system, the reverse chimes will be lost
RP4-CH21
RadioPRO4 Interface for Select 2013-2018 Chrysler Vehicles with CAN bus
Installation Instructions
It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software.
Detailed Instructions
- If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
- Download the firmware file to a location on your computer that you can easily find.
- Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
- Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
- Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
- Select your RP Interface from the "Interface select" pull down menu.
- Click "Update firmware". The new firmware can be found where you saved it before beginning.
- Once the files are chosen the update will begin. When successful it will show the text "End Update".
IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.
- Firmware Download, Version 5.1.2 (Released on February 13th, 2015)DownloadRelease Notes
- Adds Alpine VR command
- Utility/Other, Version 2.6 (Released on July 21st, 2017)DownloadRelease NotesPAC-UP Interface Updater
- Utility/Other, Version V3 (Released on June 16th, 2014)DownloadRelease NotesVehicle Settings Application
An all-in-one radio replacement and SWC interface, the innovative RadioPRO4 comes pre-loaded with amplifier retention and SWC software, navigation-based output signals, and other features that save time and money during installation.
- Data-controlled accessory and navigation outputs.
- Built-in pre-programmed SWC retention
- Retains factory amplifier
- Retains factory Back-Up Camera
- Retains Climate Controls that are lost when removing the factory radio
- Retains Blind Spot Detection system
- Retains Lane Departure Warning system
- Retains Vehicle Settings menu (when used in conjunction with a PAC-UP)
- In package updatable using the PAC-UP
- RP4-CH21 Instruction Manual
- Rev 2
Download (1002.6k)
